Technical Specification
Feature |
Implementation |
Power supply |
Single supply voltage 6.0V – 24V (5V customize) |
Frequency bands |
● Quad-band: GSM850, GSM900, DCS1800, PCS1900. ● The module can search these frequency bands automatically ● The frequency bands can be set by AT command. ● Compliant to GSM Phase 2/2+ |
Transmitting power |
● Class 4 (2W) at GSM850 and GSM900 ● Class 1 (1W) at DCS1800 and PCS1900 |
GPRS connectivity |
● GPRS multi-slot class 12 (default) ● GPRS multi-slot class 1~12 (configurable) ● GPRS mobile station class B |
Temperature range |
● Normal operation: -35°C ~ +80°C ● Restricted operation: -45°C ~ -35°C and +80°C ~ +85°C 1) ● Storage temperature: -45°C ~ +90°C |
DATA GPRS: CSD: |
● GPRS data downlink transfer: max. 85.6 kbps ● GPRS data uplink transfer: max. 85.6 kbps ● Coding scheme: CS-1, CS-2, CS-3 and CS-4 ● Support the protocols PAP (Password Authentication Protocol) usually used for PPP connections ● Internet service protocols TCP/UDP/FTP/HTTP/SMS ● Support Packet Switched Broadcast Control Channel (PBCCH) ● CSD transmission rates: 2.4, 4.8, 9.6, 14.4 kbps non-transparent ● Unstructured Supplementary Services Data (USSD) support |
SMS |
● MT, MO, CB, Text and PDU mode ● SMS storage: SIM card |
FAX |
Group 3 Class 1 and Class 2 |
SIM interface |
Port SIM card: 1.8V, 3V, Protected against ESD with a TVS diode array. |
Serial interface |
● Support from 4800 bps to 115200 bps, default auto baud rate ● Support RS232 ● Embed standard AT command(GSM07.05 and 07.07) |
Phonebook management |
Support phonebook types: SM, FD, LD, RC, ON, MC |
SIM Application Toolkit |
Support SAT class 3, GSM 11.14 Release 99 |
Physical characteristics |
82*47*15mm |
Pin Description
PIN |
Name |
1,4,6,7,8,9 |
NC |
2 |
TXD |
3 |
RXD |
5 |
GND |
Mode |
Function |
|
Normal operation |
GSM/GPRS SLEEP |
The module will automatically go into SLEEP mode if DTR is set to high level and there is no interrupt (such as GPIO interrupt or data on serial port). In this case, the current consumption of module will reduce to the minimal level. During SLEEP mode, the module can still receive paging message and SMS from the system normally. |
GSM IDLE |
Software is active. The module has registered to the GSM network, and the module is ready to send and receive. |
|
GSM TALK |
GSM connection is going. In this mode, the power consumption is decided by the configuration of Power Control Level (PCL), dynamic DTX control and the working RF band. |
|
GPRS IDLE |
The module is not registered to GPRS network. The module is not reachable through GPRS channel. |
|
GPRS STANDBY |
The module is registered to GPRS network, but no GPRS PDP context is active. The SGSN knows the Routing Area where the module is located at. |
|
GPRS READY |
The PDP context is active, but no data transfer is going on. The module is ready to receive or send GPRS data. The SGSN knows the cell where the module is located at. |
|
GPRS DATA |
There is GPRS data in transfer. In this mode, power consumption is decided by the PCL, working RF band and GPRS multi-slot configuration. |
|
Minimum functionality mode (without removing power supply) |
Use the “AT+CFUN” command can set the module to a minimum functionality mode without removing the power supply. In this case, the RFpart of the module will not work or the SIM card will not be accessible, or both RF part and SIM card will be closed all, but the serial port is still accessible. The power consumption in this case is very low. |